Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
hi guys!
i'm trining to develop the nrf 52840 devkit in particular for the ble use.
from the documentation i didn't find anythingh about send a message to the dongle from...
Hello guys,
I am using nrf52832(PCA 10040) and transmitting radio packets. I want to collect the packets using raspberry pi. Is it possible?. If yes, how are the ways we...
Hi, everyone. I've been trying to migrate from the SDK 14.2 to 15.2, but I've been having trouble getting one new function to work. I previously used ble_advdata_set() to...
Hello,
I've checked a few related threads, but without any success.
I need to react on "Data Ready Interrupt" and read data from SPI. SPI and Device is initialized before...
I'm am trying to select an LDO to provide the VDD_GPIO power rail for the nRF9160 and am interested in selecting either a 100mA or 200mA LDO. Can Nordic provide a rough order...
Hi,
I was trying to communicate with an I2C device, which's address is 0x7C
But I always got NRF_DRV_TWI_EVT_ADDRESS_NACK event, so I took a check on the TWI wave:
...
Hi Nordic Team,
Meanwhile we are working with Laird BL654 which uses the nRf52840.
My questions:
1. Can we flash gazell examples on Laird BL654 with Segger?
2. If...
i'm trying to get distances between nrf52840 ble transmitter and receiver, using measured rssi upon receiving ble_gap_evt_adv_report_t from ble stack. in order to calculate...
In file sdk_config.h, in order to configure a calibration interval of 8 seconds, what number should be used in the define NRF_SDH_CLOCK_LF_RC_CTIV?
The time units are not...
Good day,
I again have an interesting question). There is a useful descriptor to better understand the purpose of the characteristic. This is a 0x2904 handle (GATT Characteristic...
Hi,
I want to know what event DEV KIT jump into when mobile provision complete for DEV KIT (100% , not bind app key and pub sub address). My idea is in provision process...
Hi!
I am currently evaluating the nRF91. For testing reasons I want to enable the debug logging for the lte link control. I checked the Zephyr documentation etc. but I was...
Hi everyone,
I am implementing a custom protocol using the NRF52 radio, and so far I was able to make the transmitter working as expected.
In a nutshell, the protocol...