I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
When adding two more characteristics to my custom service, I get error #4 which is an out of memory error. The log is working but it does not show the settings for what I...
Hello,
I'm working with SDK 15.0 and Softdevice S132 6.0. I have two nRF52832 boards (the BMD-300 Evaluation Kit and the SparkFun nRF52832 Breakout ).
I am running ble_app_hrs...
I am quite confused about how to go about programming the nRF52840 Dongle. The "programming" page on infocenter says that it can be programmed through the nRF Connect Programmer...
Hi everybody!
I would like to ask the following nRF52840 has the function of preventing current reverse irrigation?
Or what circuit prevents nRF52840 current from flowing...
Hi,
We're designing a BLE module, which is fairly straightforward. The design contains a nRF52832 + SKYWORKS SKY66403-11 FEM. We set the nRF52832 to transmit at -4 dBm and...
Hello,
I'm working on Keil with SDK 15.0 and Softdevice S132 6.0. I'm trying to run the Nordic UART Service example. I have two nRF52832 boards (the BMD-300 Evaluation Kit...
I have quite a few SPI peripherals to be interfaced with nrf52840 chip, for example, Ethernet plug, ATWINC1500 WIFI module etc. What example should i start with to get an...
Hello,
I am using NRF52840 and NRF52832 SoCs for different roles to be played in a BLE Mesh Network. As of now i am using NRF52840 DK and Holyiot-17095 for evaluation purpose...
Hi everyone,
I went into the bootloader mode with the nRF52840 DK accidentally so I immediately turned off the DK and powered it back on. However, after powering the DK...
Hello all,
We are using nRF24L01+ as Rx in an embedded system and we are experiencing the following problem:
The MCU that operates the radio can be manually reset (a...
My nRF52 DK has PCA10040 V1.1.0 2016.34 682272915 on a label.
It works fine when connected to my laptop over USB. If I try to power it from the coin battery underneath though...
Hello, we are using a radio module with the nRF51822 for our telemetry system.
In order to conduct the EMC test of EN 301 489-1, I would like to clarify the 6dB bandwidth...
This is a duplicate of this issue of pc-ble-driver-py repository.
While using pc-ble-driver-py on MacBook without problem, I face Error 13 when opening device on Raspberry...
