I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi
Over the last years working with Nordic I struggled from time to time over the disconnect reason 0x3E (BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED) on our devices with Central...
hii...
i have programmed the ble_uart with twi sensor ...
complied very successfully
but while i am debugging i am getting error in void twi_init()
why and also fatal...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
IDE: keil uvision 5.23, SoftDevice 3.0.0, SDK 12.1
Computer Platform: Windows 10
Receiving device: nrf52832_xxAA
In our project, there is a sender always advertising...
Hi,
I have a project where, I need to change the minimum and maximum (MIN_CONN_INTERVAL and MAX_CONN_INTERVAL) connection interval to higher values like 1 second and 2 second...
hi everyone!
I am developing NRF52840 with the Development Kit.
I am trying to use a GPIO to o capture a external HIGH-TO-LOW signal and then trigger a LED.
I I learned...
Hi all,
I'm currently using nRF Connect in combination with a nRF52 DK to connect to my Mesh network. So right now I have to type all my commands as HEX messages and decode...
Hello,
I'm trying to compile the Light_switch_provisioner example (Debug, Mesh 2.2.0) in Segger Embedded studio.
<t: 0>, main.c, 561, ----- BLE Mesh Light Switch Provisioner...
hello
i wanted to send message using the simple message model with some modifications from client to server periodically but didn't know from where i should start , i tried...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
Hello All,
I am developing an application using Nordic nRF_SDK_15.0.0, in which I need to make my BLE peripheral device as a peer device which will get/set data from/to...
