Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am trying to initialize the BLE NUS UART service and the BLE LBS service so both can be used at the same time in a single nRF52 application. I can initialize a single service...
Hey,
I was reading about nRF5 IoT SDK and it all looks amazing, I am really shocked. There is only one bottleneck I can see right now and I am not sure if there are any...
nRF_log_1.8.1.txt Hello Nordic Support Team,
We are trying to run the OTA DFU on the nRF51 device via the nRF Connect iOS application V1.7.5.
The DFU Device is available...
Hi,
I'm trying to evaluate the IAR simulator, and I'm using it w/ nRF52 samples. Besides getting errors due to the errata and system init, I'm not sure what are the use...
Hello, I was wondering if it was possible to simulate the nRF52 board using the simulator in Keil. I am trying to use it as a SPI master and it would help to be able to simulate...
In our application we use gazell. We also want to use the flash data storage which uses softdevice.
With gazell enabled, we cannot access flash.
What is the recommended...
Hardware: nRF52 DK
Example: ble_app_hrs
I have a problem with starting program using debugger. I starts debugging session and starts program using resume button, breakpoints...
I'm trying to configure SWO properly, specifically to get the output in Eclipse. The following code is used to initialise the SWO.
I have a snippet that outputs a string...
BLE is always running on Arduino Boards PROMO and PRIMO CORE
Even small example Sketches like Alarm Interrupt who doesnt use BLE functionality in the code enable the RADIO...
hi sitting and looking at the light demo example through and looking at where I do not quite understand what p_args is used to, so someone can explain that thanks: D
Hello Sir,
In last my custom nRF52832 PCB i have use 100nF capacitor mft part no: "C0402C104K4RACAUTO" but now it is nor available in digikey.
So please sir provide me...
Hi all,
Is it possible to get a softdevice which can do 2dBm output? Our device is very power critical, but we would like to have as much power as possible.
At 4 and 3dBm...
Hello, I'am working on the code of ios-nrf-beacon( github.com/.../IOS-nRF-Beacons).I found the code with Objective-C,but I'm working with swift,I want to know if there is...
What is the proper way to use the Queue Library and define a queue that can be used across multiple C files? I have the following code a my common header
NRF_QUEUE_DEF(uint8_t...
