Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I'm wondering if there is an example for scanning and advertising at the same time during a connection as peripheral? Or is there an example where I can start from...
Hi, trying to upgrade from V12.3 to V14.2 with a nrf52382 and SD 132.
I'm stuck with nrf_sdh_ble_enable returning an error code - unfortunately, the SDK documentation does...
Hello,
I will be using the NRF52 to send out advertising btle packets.
I am curious if anyone has any idea if the radio is strong enough to still send out packets if...
Hello
Is there any possibility to get receiver IF to any package pin. Even some kind of factory debug mode.
Normal receive functionality during this is not needed.
...
Greetings, we're currently working in an application where we need to connect different peripherals to a nrf52832 for a wearable device. Each of these peripherals uses a different...
Hi:
i write very simple BLE App, it used open link. No security/encrypt. 1 service with 2 characteristics.
tx(serviceTXID, rxBuffer, 0, sizeof(rxBuffer), GattCharacteristic...
Hi there,
I wonder why I have to flash my nRF51 DK using mbed build first to make the SDK build work?
I received my 2 nRF51 DK today and I tried the first one in the...
Hello
I am new to Nordic's product line. I would like to know if there is a recommended Bluetooth 5 SoC for wearable products that require years of battery life. For example...
Hello, I am trying out my pca10028 board, with s110 and my updated ble_app_uart expample. I am trying to detect a link loss: board advertises as peripheral connects with android...
Hello,
I work on module BLE LAIRD BL652 and I'm a BLE peripheral. I have tried to make a BASIC program for advertising while in a connection but without success.
As...
Hi,
i am creating a new project iar workbench 7.8 with SDK V8.1.0 and softdevice V8.0.0 using custom board nrf51822 ic revision 3 (QFAAH00),clock source as "NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
Hello Sir,
I am designing PCB using nRF52832 SoC it is very small and operated on AA battery source.
So please recommend me for reverse battery voltage protection diode...
Hi Guys,
Me again. I was thinking someone could provide some suggestions on my understanding of the BLE connection ( porfile, GATT, characteristic,value, etc...)
I finished...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
