Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All,
The MTU_SIZE of ble_app_uart is set to 64-byte. When write data over this, let's say 80-byte, the program will be reset.
I don't want to increase the MUT_SIZE...
Dear friends,
My PPK works unstable. Sometimes it works well, while sometimes it won't start. When it is started from the command line console, the error output is "initialization...
I have been working on "merging" SDK for Mesh's lightswitch client example and SDK v14.2.0 UART server example, mostly following the document on this site , with some changes...
I've gone through the user manual for the Nordic Power Profiler Kit, but I can't find any basic information on how to understand the plots and the measurements reported under...
I would like to have one central and two peripheral connection. Ad functionality required is same as NUS UART Example. But the example code connects to only device. Can any...
Hello,
i would like to connect two Redbearlabs Nano v2 just with eachother. The central one connects just to the peripheral, but the peripheral is still open for every...
Hello There,
I found following dongle based on nRF51822.
They claim same will work for bluetooth 5.0 also.
I know BT5 devices are not backward compatible, so not sure if...
Hi,
How can I share a GATT server profile constructed on nRF connect for PC with nRF connect for Android ?
'Save/Load setup' on Windows PC stores/Load json file
In...
I've got a set of boards that are behaving very strangely. I attempt to turn on the HFCLK but the HFCLKSTARTED event never comes nor does the HFCLKSTAT register indicate that...
I cannot suffer this tool anymore. As u can see in the pic below, it provides a cursor mode to measure the currents of X1/X2. However, users always need to know the average...
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
Hi,
do sd_flash_page_erase or sd_flash_write provide any guarantees that the command has executed successfully or should I do a manual check to verify if the page was really...
Hello all,
I am working on nrf52832 Board and i want to use it as translator to send and receive the data , please tel which pins i need to select as UART(rx,tx) pins ...
