I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Preface: I am developing a software working with different radio protocols (enhanced shockburst, bluetooth,...). Therefore I implemented uart commands for switching radio...
Recently i have purchased nrf51822 and nrf51dk but i dont know how to flash softdevice in nrf51822 using nrf51dk.
please expain me how can i flash or where can i know how...
Hello,
I have a problem running nRF51822DK with temp. sensors while running BLE. I tried DS18B20 but it doesn't work at all, then TMP36 with ADC reading and as it works ...
I have spent almost one day trying to make sense of that.
NRF52832 is SPI Slave, based on your examples/peripheral/SPIS/pca10040 sample
SDK v12.2.0
board DK PCA10040...
I am trying to implement IR reception using TSOP1738, more specifically Vishay's SM0038.
I have set the GPIO pin to call an interrupt whenever there is any change in the...
Hi all,
is there a tutorial about this topics? It's not clear to me how create a whitelist and i have a problem with events BLE_ADV_EVT_WHITELIST_REQUEST that not occurs...
its my first program at RTT .I have open the ble_app_uart project from examples of sdk .and fallow the tutorial devzone.nordicsemi.com/.../ .
program compiled and load successfully...
I use mac os x sierra on MacBook pro 2016. And I followed this link .
I took following things in order.
I moved gcc-arm-none-eabi-5_4-2016q3 to /usr/local/gcc...
Hello
i have made a program to smoothly blink/fan/vary the intensity of 16 LEDs together using 4 PWM with 4 output pins, the program seems to work well with around 4 leds...
i am using nrf51822. is it possible blutooth communication without softdevice. if possible, please explain me how. if not why. please help me any one.
thanks in advance...
Hi,
I am running an application in which I set -D__STACK_SIZE=0x4000. After some research, I come to know that RAM is divided into 4 blocks the lower one is for the soft...
Hi
Because the dfu_single_bank.c file is not functional over BLE, I'm trying to modify the dual bank configuration to single bank. The modification should be very simple...
Hi,
I am using nRFToolBox into my smart phone of v4.4.2(kitkat).
I am trying to update my program using OTA through my phone.
But when i am trying to send dfu_test_app_hrm_s130...
