Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hello,
I would like to return a specific error when a device connects to my NRF52 (by bluetooth) when for example the range of mac address is wrong to me... (or something...
Dear Folks,
I have a question regarding the supply rise time of the nRF52-Series.
According to the Product Specification Chapter 6 Table 8 the Supply rise time (0 V...
Hi, I encountered some problem using the S132v3.
With the s132 v3 and sdk12, I want to extend the ble transfer size.
Now I can change the att_mtu to 100, and iphone...
Hi all!
I recently ordered BLE tag with nrf51822 QFAB chips.
When I read back the memory content (with mem8 jlink command) I manage to read up to the address 24A60 which...
The task I am working on is sending a list of records from an nRF52832 chip to a central. Before sending the records, the total number of them should be sent, so the central...
Hello. I'd like to know. Can I trust to opportunite to firmware my controller (nrf52832) over the air. I mean is there any chance do not be able to do it, for example if last...
I'm using a module that has nRF24L01 mounted.
When I transmit to many PRXs, using the same frequency and channel, I expect to receive
many ACK signal at the same time.
...
I'm using nRF24L01 in a star network and i want to disable ACK.
I write the ACTIVATE command followed by 0x73, then a write to register FEATURE the value 0x01.
In this way...
I am trying to follow the tutorial given on this page:
devzone.nordicsemi.com/.../
However, my eclipse project does not build and created following log
13:55:03 ...
app_pwm_uninit is hanging the code. The control goes to pwm_dealloc() and then in nrf_drv_ppi_channel_free() it hangs.
Using SDK10. I want to change the PWM frequency and...
I am new to eclipse IDE and I am following tutorial on this page:
devzone.nordicsemi.com/.../
I am able to make the blinky project on the terminal and it does create...
Hi,
I have the following piece of code.
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<300;i++)
{
nrf_gpio_pin_clear(PIN_EN_BSTR);
__NOP();
__NOP();...
Hi,
I’m trying to use new SKD 12 secured bootloader but can’t pass signature check in dfu_req_handling.c\dfu_handle_prevalidate() (code after switch case DFU_SIGNATURE_TYPE_ECDSA_P256_SHA256...
Per table 19.4.2 in the nRF52 PS v 1.1:
, what is the difference between CL (load cap) and C0 (shunt cap)? The max ESR is specified for C0 but not CL. The xtal datasheets...
