Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
During some recent development work it was noted that there is no PA LNA assist in the DTM software. Is there code that provides this?
See answer below:
Hello,
I have a project that started out as a Peripheral BLE_HRS example. I am currently running SDK 9.0.0.
I am able to Bond a nRF51 Central with a nRF51 Peripheral...
Hello,
I'm using the SDK 11.0.0 and S130 on both sides, and the projects ble_app_uart_c and ble_app_uart to connect a central and a peripheral through BLE. I was doing some...
Hi..
i am using nrf52 and my custom made android application.
softdevice is 132.
in that am able to do DFU for application file with android master control panel.
i used...
Hi.
I will make clock.
I use RTC2 + Softdevice. (PCA10040 , NRF52832 , s132_nrf52_2.0.0_softdevice.hex )
Base Source code = nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral...
It seems to me that Nordic has implemented only a part of the Current Time Service.
I want to get the time zone in addition to the year, month, day, hour, minute, second...
Hi.
I'm developing firmware based on github.com/.../S130_LBS_client_server_central_peripheral example. I installed third party Softdevice s130, and with example of peripheral...
I have modifed the nus_uart(peripheral) to add static pass key in sdk 10.I used my mobile phone to test the functionality and it works as expected[asks for the passkey when...
Hi,
I'd like to put a BLE central in low power between two scan.
actually I use the example Ble_app_uart on a dk board PCA10028
and a second dk board as advertiser with...
Hi,
I am trying to get the SPI Slave working but was hoping to find a how-to. Is there an example of the SPI Slave for the S110 Soft Device (7.3.0)?
Currently, I am...
Hello,
I am developing custom HAL driver for SPI in NRF52 (PCA10040). The problem is that using the EasyDMA MAXCNT registers value must be between 1...255. It implicates...
Hi,
I am using nrf_pwm_noglitch.c from here . Is there a way to stop the pwm cleanly?. I would like to have a nrf_pwm_deinit(); similar to nrf_pwm_init(). Currently I set...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
About "ble_app_multilink_central" for the reference.
This code shows me below sequence.
Scan->connect request->get connection...
