Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
Hello Nordic Devzone.:
When studying the 8.0 BLE Central multilink example (s120 softdevice), I looked into the component relevant to button pressing interrupts, app_button...
How do I use the NRF51 or 52 to create a GATT server with read only service without requiring bonding? Basically I want to be able to provide more data than advertising allows...
I can not connect to one of my beacons, i need to reset its config, but HW way.
Can i reset it somehow?
It is nRF 51822 based, sensoro 4AA. I asked sensoro 3 days ago...
Hi Nordic guys,
we are using uart for communication with another MCU and flow control is used.
Beside the uart communication itself we have out of band signals (on gpio...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
Hi can anyone guide me in configuring the peripherals of nrf51822 before putting the chip into sleep? For example, timer, i/o pins, etc... which is not needed to reduce the...
Hello, please help me to find nRF52 datasheet, in which are recommended WLCSP footprint, and of course schematic drawing of this module. In your Dev Zone I found only QFN...
Hi,
I'm wondering what speed the NRF52832 radio is clocked at internally. is it the main 64MHz clock or 16MHz like the NRF51?
The reason I'm asking is that I would like...
