Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Is there a way to figure out for which target a binary in _build/ is compiled with Keil?
(other than parse .map or .lnp file for a file unique to the target)
hi , I am trying to download the softdevice(v8) and cross compiled application(using makefile in nrf51822 sdk v6) from my Linux PC using JLinkExe.
following is the memory...
if i am a master i want know to know the sleep period of node,how do i know...?
how do i know whether it is sleeping or awake..?
if i have data to sent for node,but...
nrf51822_AA rev3, SDK8.0.0, S110 8.0.0
My application has the max number of bonds set to 24 with a size of 128bytes each. So that's 3 pages. Plus one page for saving user...
Hello,
I want to generate timer events as exact as possible, based on a time base that is defined by a runing timer. For example, I've setup timer0 to count up every 1µs...
Hello,
I want to use the Segger drag and drop programming feature on the PCA10028.
I have got a running application with the S120 softdevice.
To use the mass storage...
After 6 days hard work finally completed a C++ class to implement MultiCeiver and Enhanced ShockBurst….
But the “Product Specification PDF” contains some errors:
a) Page59...
What's the best way to ask the device manager how many bonds it has? Or even, whether it has any bonds at all?
I can see nothing in the API docs here:
developer.nordicsemi...
Hi all,
I asked this question before but I am not able up to now to find solution. How to use DFU example of SDK 7.1 for the S130 SoftDevice. I have tried some flash address...
I am currently developing a bootloader for N548 chip from Dynastream/Nordic.
I am following the project example for the S310 soft device and using IAR.
The project had been...
So I see ble_app_hrs and others have some nice examples of buttonless reboot into DFU bootloader. But for security reasons, I'd rather the user hold down the reset button...
hi, I am very new to ble and I am trying to download softdevice S110 to my Yunjia NRF51822 board. I am using J LINK connected to my linux PC to download the softdevice to...
Hi：
I used a design with nRF51822-QFAA+BAL-nrf01D3+Pi-network+SMD chip antenna,but it didn t work well.I tested the VDD_PA Pin ,it didn t have a 1.6V voltage(datasheet),that...
Hello,
I am trying to adapt a bootloader from sdk examples to my nRF51822 board without success.
I am able to adapt the example apps from the SDK (I have to change the...
