Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Is there any Nordic Sermiconductor Wireless 2.4Ghz product through which i can communicate with other wifi (IEEE 802.11) and Bluetooth devices ? At-least the device must obey...
Hello Community,
Does anyone know how to read/write configuration registers (UICR, FICR) on nRF51822 in a linux environment ?
So far, I have to stick with Windows for...
Hi
Please tell me someone about the causes and countermeasures!!
I Connect the board & JlinkLite and tried the flash write.
Softdevice Ver6.2.1 -> Success
Softdevice...
Unfortunately, I'm not seeing NRF_EVT_POWER_FAILURE_WARNING events on my s210 based system. As I've seen in other questions on the forum, I've implemented the calls below...
I'm currently trying to merge the S120 softdevice with the compiled code from the ble_app_multilink_central sample under Linux (Ubuntu).
Here is the command I'm executing...
There are a couple problems with the SDK 7.1.0 implementation of nrf_delay_us for GCC. The experiments I've run show the provided version generates delays 40-50% too long...
Hi,
I am developing an application to capture data on a PC over ANT+ using the ANTUSB-m as slave and the nRF51 DK as master.
In order to test my program I want to be able...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I am trying to use the nrf51822 to send media button commands over HID. I have seen several questions on here and they usually involve the HID Mouse example (which doesn't...
Hello,
I have been trying to implement AES in order to encrypt a time stamtamp to be sent in the advert of the iBeacon ( 128 bits, using Minor and Major bits, (16+16)*4...
Hi,
I am trying to decrease circuit power consumption that's why I am using sd_ble_gap_tx_power_set(TX_POWER_LEVEL) function. When I set TX_POWER_LEVEL as 4 or -20, I dont...
We are looking to change tx_power setting to Neg30 dBm and for this we have accessed NRF_RADIO->TXPOWER = (RADIO_TXPOWER_TXPOWER_Neg30dBm << RADIO_TXPOWER_TXPOWER_Pos);
...
I have the NRF51 DK working with CrossWorks on OSX. I have the blinky example working.
Now I would like to figure out how to get very basic HELLO WORLD type demo to iOS...
I am implementing dual bank DFU on the PCA10001 board using the latest SDK (7.2.0) and S110(7.1.0). I am able to enter bootloader from my app as detailed here:
developer...
