Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
I have a Thingy:91 board that appears to be broken, no response either on the LED or via USB UART when switching on.
I've earlier done some development with it, and hooked...
Hello,
I am attempting to follow along with the AWS IoT example. Everything has gone OK so far (Create a Thing, Create a Policy, Create and download certificates) until...
Hi All,
In our product we have noticed that, on a few occasions, some important information that is saved using FDS (in a file with ID: 0x02) are being erased when an OTA...
Hi,
Do you have a recommended circuit for supplying VDD_GPIO with the right timing relationship to VDD?
Section 11.1 of the datasheet says "VDD_GPIO should be applied...
Since the 9160 will vary his transmit power based on signal strength, is there any way of determining what power is being used for a given transmission? I know that the max...
The Edge Impulse firmware compiles and flashes to the Thingy53, without problem. I would like to increase the range of the BMI270 accelerometer, but can't find any reference...
I am using 52840 and SDK V14.2.0. When compiling nrf_ble_dfu.c I see the following error in nrf_dfu_types.h: line 258
"two or more data types in declaration specifiers....
Hello,
I am getting 0x07 error code when invoking sd_ble_gattc_char_values_read(..) function.
I am using SoftDevice 140 v6.1.1 APIs. I have an NRF52 dongle and I programmed...
