Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am using a nrf52833 with NCS and was wondering if there are events I can subscribe to (or polling if events don't exist) that will notify me when USB power is connected...
Hello,
after some trial and error, I managed to use the "Bluetooth: Direct Test Mode" example with NCS 2.7.0 (Sysbuild) and USB.
Now I'm questioning myself how to correctly...
Hello,
I want to know how I can complete the qualification process. I already have a Bluetooth account. I tried to go through all the steps, but the only things I needed...
Hi, Encountering an error while trying to program a custom board connected to the nRF5340 DK via P20.
The external board is connected to the nRF5340 DK through the P20 connector...
Hi all,
by default, the "nRF5340: SMP Server with external XIP" sample does not support reverting images in case DFU was not successful. In other words, it does not swap...
Hey, everyone. I am currently working with NRF9160, NCS V1.3.0, developing code for an application that requires periodically storing important information in flash, and send...
Hi,
I'm trying to store the DFU image in external flash. I already have DFU on the internal flash working.
When I enable support for the external flash and perform a...
I am developing a .NET C# project that receives data from the Nordic nFR52840 BLE Dongle via BluetoothLE, does Nordic provide any specific libraries for this purpose, or if...
I am migrating from the 2.6.1 development environment to 2.9.0 but am unable to compile due to some configuration issues.
My prj.conf configuration file is as follows: ...
Hi,
Recently I upgraded to nRF Connect SDK 2.6.1 and I was required to enable the GPIOTE in order to build properly. Doing this has significantly increased (nearly doubled...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
I’ve been working on creating a C++ application based on the NUS example, but I’m encountering an error. I’ve attached my application below. All I did was enable CONFIG_CPLUSPLUS...
ncs_add_partition_manager_config does not appear to be working. I am using ncs 2.1.0 and doing a build with MCUboot. Am I doing something wrong below?
I am using the following...
I open up a flash shared space in app and bootloader, write values from app, bootloader read, bootloader read values such as 0xFFFFF, and not ideal values, may I ask why this...
Hi, I'm upgrading the ncs version of my project from v2.7.0 to v2.8.0 and I'm no longer able to compile the project due to a linker error because the websocket_connect function...
