Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I was using SDK 1.0.0 earlier.
I ported my code to new SDK v1.0.0.
But i am getting undeclared macro error as shown in below image
In prj.conf i have initialized...
Hi All,
I have arduino ble 33 ble device and able to connect with it using my android application using BLE library. I am trying to write 9000 or 18000 of UINT16 by converting...
hi ,,, i am getting the four data from various sensors, then i want to combine all the four data and send in ble_app in variable , example x=10;y=30;z=34 using sprintf i am...
Hi,
I want to use the nRF Mesh SDK on nRF52840 chip with proxy client role that can send messages over GATT connection to proxy server role device. Is that possible?
Currently...
Hi Nordic,
Chip set: nRF52840
SDK: 15.3.0
Softdevice: S140 (06.01.01)
Button interface with MCU: Total=13 (All with GPIOTE)
We have face one blocking issue at...
Hi, Greetings !
I have totally 3 services and 8 characteristics added in my project. In first service there are 2 characteristics, 2 nd service there are 5 characteristics...
Hello Support Team,
I am using an nrf52832 module in our project. During testing, we have observed that the BLE firmware gets stuck and it stops advertising further when...
HEllo; I'm working with nrf52832 and sdk15 , and for interrupt button i chose to work with the example "/nRF5_SDK_15.0.0_a53641a/examples/peripheral/pin_change_int/" , so...
I am interested in having nRF Connect Desktop Bluetooth low energy app work with my PCA10056. From:
https://devzone.nordicsemi.com/f/nordic-q-a/40155/custom-board-support...
I am trying to connect two peripherals to one central. I do not understand the settings for connection interval and gap event length.
For example, this would result in...
In order to interact with the UART, you need to first declare a device struct and then get a binding to the device:
Then in order to switch the UART on and off you...
I use two nRF52840 to send notifications every second. Analysis using a logic analyzer revealed that the reception interval had strange variations. What is causing this? Why...
I am have a curious issue with thingy52-mesh-provisioning-demo repo at Nordic Semi github.
Prebuild hex behavior does not match with hex compiled by source.
In short,...
hie,
i trying to storage the data in flash and read it. i am unable to read the flash .i have attached my code.please correct me if there is any mistake.
Regards,...
