I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hello,
I'm trying to autoconnect my device to my phone using nrf Connect app. I connect to my board selecting autoconnect flag, then insert my passkey and devices are correctly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
Hi,
I am trying to run the ble_app_uart_coexist example on my nRF52840 Development board.
I followed the above steps for configuring the example to work.
I copied...
how to include SPI Master code in ble_app_uart sample code of pca 10028(nRF51822) board. its soft device is sdk 10.0.0 (s110). Please share me a sample code if you have. ...
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
