Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
By taking a look at the source code in https://github.com/NordicSemiconductor/pc-nrfconnect-rssi.git, I found the following patch file under fw/src/usbd.patch. It mentions...
We use nRF52840-PDK (PCA10056) with MCU revision Q1AAAA. Given example of secured DFU bootloader (s140) works good. Then we changed MCU on this board to the MCU with Q1AAC0...
Hi to all,
i am working on a project that in it i want use nrf51822 as a peripheral device. i implemented a code but i have a problem, central(cc2540) and peripheral(nrf51822...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
I am trying to migrate a blocking SPI transfer code to a non-blocking SPI Manager schedule call. I have 16 transfers queued up in one transaction.
When I launch it, the...
What is the best way to advertise a custom service and allow BLE connections from a mobile device in a Mesh SDK version 2.0.1 application. Previously I had an application...
Initially I had a project in Mesh 1.0. Everything (provisioning, send&receive) was working fine.
Since upgrade to the Mesh 2.1 there is an issue: provisioning still works...
Hi I've found the documentation around BLE_GAP_TX_POWER_ROLES to be a bit sparse. I was wondering if someone could please give me some more info on them
Three roles have...
I am trying to get the thingy52-mesh-provisioning-demo to work with the SDK for mesh 2.1.1 and nRF5_SDK_15.0.0_a53641a.
I am using the Segger Embedded studio project from...
Hi I'm developing DFU project for my application. I need to have both BLE and UART bootloader. If possible, how can I do that?
Many thanks for the answer
Abele - Ital...
Is there any other way for connecting nRF52 DK with our smart phones, other than through NFC?
My smart phone dosen't have NFC feature and I want to run and test the BLE...
