Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
Hi all,
I'm starting with fcc and etsi test! i know that the radio test example is useful to test the radio.But the ETSI add two type test about receive emission spur and...
Hi!
So I managed to create my custom service with one characteristic (a struct with several attribs).
I can see it in my app and everything's awesome. Yay.
But in some...
I have been experimenting with the mbed BLE Health Thermometer examples, BLE_Themometer etc. Whilst they are visible and show their name in the nRF Toolbox Health Thermometer...
Hello,
with Android 5.0 BLE central and S110 8.0 peripheral I do this:
Erase all bonds in device_manager_peripheral.c
Check that m_peer_table contains zero...
Hi,
I would like to convert a blinky project for the BOARD_PCA10040 to my own custom board. I can't find on eclipse where "#define BOARD_PCA10040" symbol is defined so I...
Hi,
I'm trying to config my device with resolvable private addr (RPA) as code below:
rpa_add.addr_type=BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE;
sd_ble_gap_address_set...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
