I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi.
I've played around with the android application (based around google gatt example, but used in gatt server -mode).
How is the example expected to be handled? In...
Hello everyone,
I am currently trying to make simple exchanges with an NFC chip using SPI.
Configuration is: nRF52 on dev board 10040 with example from SDK12 located...
Hi,
I have such code:
static buf[9] = {initializers};
for(i =0;i <9;i++){
while(app_uart_put(buf[i]));
}
I always get "0" before the actual buf content and the...
Hi
I've implemented a peripheral with bonding support by the peer manager. Additionally the device should scan for bonded devices by using a whitelist. I used the function...
Hi,
I'm trying to compare two RC networks by using GPIOTE, PPI, a Timer and the comparator to measure the time needed for a charge and discharge cycle for each of the networks...
Is it possible for one Arduino Uno to have a BLE nRF8001 module and a nRF24L01+ module wired to it (allowing each module to communicate simultaneously)? According to the wiring...
We are trying out the new nRF5x SDK v12 and it looks like the previously working ble_app_hids_mouse example is broken now.
It compiles successfully, but as soon as we try...
I have observed that the Radio Notification from ble_radio_notification.c becomes inverted sometimes. I saw this post about the same problem:
devzone.nordicsemi.com/.....
I would like to use nRF5 SDK for IoT with some functionalities (e.g. SEGGER RTT) from nRF52 SDK. Can I just copy desired modules to my SDK for IoT and suppose it'll work?...
Hello,
For some industrial reasons, I need to store the passkey in the flash of the nRF5 during production and retrieve it at run-time.
I would like to know if there...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
Hi all,
i am using V11 sdk.
i want to send data "hello" in beacon application.
how to add that feature.?
any function calls are there?
-Thanks in advance
Hi,
I am using a PIC microcontroller in my project (18F family) and I would like to know which are the tools needed to begin development with the NRF80001.
I already...
