I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
I've got 4 services with 15 characteristics between them. Trying to add any more than that results in sd_ble_gatts_characteristic_add() returning NRF_ERROR_NO_MEM .
All...
Hi Expert,
I found a weird case that at my 51822 plaform with s110 enabled, if I define a global buffer like:
static uint8_t system_buffer[1024];
it obviously will...
Hi
The nRF24Le1 has 256 bytes in the infoPage for user data, starting 0x0100.
My question is how to write to that area?
Is it accessible from nRFgo Studio?
Is it accessible...
Hi every body,
Is there any way to increase the support packet per connection to more than 1 packet for S120 softdevice if i have just single slave and single master? ...
HI,
I have followed all the steps from devzone.nordicsemi.com/.../ and I can relay text between Termite & my iphone.
Can someone share a function / method which I can...
Hi,
I used the ancs demo of nRF51_SDK_7.2.0_cf547b5 to modify our application. It still work well, but sometime when I left the device and went out with my Iphone about several...
Hi,
I have two customs boards and on the one with the QFABA0 I can go to system off and see 0.6uA of consunption but on another board with the QFABB0 I go into system off...
Hello,The user manual describe that the NRF51822 can commuiate with NRF24L01.but,when I debug this system,There is something wrong with Address and data.I try to translate...
Hi BLE fellows,
Following the steps explained here , I have tried to integrate the OTA DFU feature & bootloader from the latest SDK to my application and tested it on my...
