Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am using segger studio and jlink to program my nordic thingy 52. I followed the documentation and
Build the program
Connect to Jlink
Erase All
Debug->Go ...
Hi!
nRF52. S132, SDK13.
I try to use ble_dfu_send_hex example.
what shoul I do first?
via nrf gostudio load SD. correct?
Which SD? from this folder (dfu_test_softdevice_s132...
I get the mesh SDK here: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
But I don't know how to add pwm to the light_switch...
Hi all,
I use the nrfjprog 9.7.1 and unfortunately I was used the --rbp command on my nRF52832 and now it's impossible to execute --recover command.
The nrfjprog log shows...
Hi,i have some problems when develop with experimental_ble_app_buttonless_dfu project in sdk12.3 on IDE embedded studio (MAC OS).
I follow this link text to develop.when...
Hello,
Some problems I meet when I try to use spi manager in ble_template example to read "who_am_i" register of LIS2DH12. The environment is set as below:
nRF52832...
Hi,
I'm using SDK13.0.0 and softdevice S132 v.4.0.2.
I sometimes get NRF_ERROR_INVALID_STATE from sd_xxx() in the function registered to ble_evt_dispatch() when connection...
Hello,
I would like to establish communication between my pca10040 and my cellular modem.
Currently I am using ble_app_uart on the peripheral example and I can put messages...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I have a thread using a Timer and PPI to trigger SAADC sampling at 100hz. Currently I have an app_timer also running at 100hz to sample the results of the SAADC (and its time...
Hi guys,
I notice that the bytes array of UUID is reversed after registerd.
For example, I define the UUID marco as follows and registe it at ble_nus_init().
#define...
I am trying to use ESB and BLE concurrently on NRF51822 SDK v11 SD130..
The BLE part is working fine but the ESB part keep causing error randomly.
I put a break-point in...
when i use C:\Users\Administrator\Desktop\nRF5_sdk14.0.0_ble_central_beacon\examples\ble_central\ble_app_multilink_central for this instance ,I debug the discover moudle callback...
The question I mentioned here
When using ble_gatts_hvx to send data, only send data pointer and length to softdevice, and softdevice did not copy these data to the softdevice...
i used pca10040_debug of bootloader_secure of nRF5_SDK_14.1.0_1dda907.
i created the key by myself.
Bootloader and zip file used the same key.
My device is in DfuTarg...
