I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
How much additional current does enabling the FPU add to the nRF52 processor? I reviewed the Product Spec. but I can't seem to find this listed anywhere.
Thanks
We successfully used the pofcon on a 51822 based design using S110 ver 7 to indicate a low batter condition to the user. However, we are moving to 52832 (currently QFAA-BA0...
I have a peripheral based on S110 that is connected to by a central running S120.
The connection is established, the S120 interrogates the service and enables notification...
Hello,
Thanks for reading this! I have an odd behavior on my nrf52832 where I am capable of uploading a new firmware via BLE DFU to the peripheral device if it is not bonded...
I'm running into something weird on SDK8.0 (I will be upgrading soon to SDK10, however it's a layered roll out so I can't update right now unless you tell me it's a bug in...
I was trying to view the scan response packet using the master control panel app I have on my android phone, but I can't seem to see where it is.
I want to update the scan...
I'm looking at an application where it would be beneficial to be able to read data from the bluetooth device as it passes. It would be easiest for me to do this by simply...
I am using the TWI module in master mode, with sdk 10. I purposely create an error situation, in which the TWI gets stuck and keeps returning NRF_ERROR_BUSY every time I try...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
Hello,
i would like to scan for a custom UUID Ventor. And when the BLE Central found this BLE Client.
I will Change one Output pin from low to high.
I start with the...
hi,
after connecting to peripheral device. app_timer_cnt_get() function always gives 0. why it is so. i am not able to understand it.
can anyone help me to get the current...
