Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
In the datasheet it is mentioned that the tx current is 10mA without DCDC. In our board, we are seeing a Tx peak current of 13.5mA. So my question is the does that quoted...
Hi everybody,
I have some troble getting the record_url sample running in my own gcc based build environment. The function calls to the nfc library always return ok, but...
Hi,
the nrf52-DK is using an molex connector to connect the Flex-PCB NFC Antenna. Due to some mechanical issues in our product we have to make the wires longer. It looks...
We are using nRF51822 module and S110 soft device.
I don't know the default value of below parameters.
・connSupervisionTimeout
・connSlaveLatency
・conSupervisionTimeout...
Hi..
i am using softdevice 132 and android MCP.
i want to create .zip file for application, but it shows error like below..
C:\Program Files (x86)\Nordic Semiconductor...
Hi all,
I am facing a weird issue trying to achieve DFU over the air with the dual-blank DFU.
I had integrated DFU with my application(Background story here .) The application...
Hi
I have problem enabling gzll on my nRF51. Error diagnoses shows NRF_GZLL_ERROR_CODE_INTERNAL_ASSERT_OCCURRED (#15), every time I try to call nrf_gzll_enable();
Here is...
I've looked at the reference manual and the several forum questions asking the same question and do not understand the answers as they all seem to point to the same docs/original...
HI All,
We are using NRF52, S132 Softdevice , SDK 11.0.0.
In SPI DMA transfer, when we try to increase size of the m_tx_data greater than 254 bytes, it failed. It is working...
HI All,
I did all the things as in this post
devzone.nordicsemi.com/.../
But Whitelist is not working for me. My requirement is this, I need to add the first connected...
Hi everyone,
I must to program my device from nRFgo Studio (rel. 1.21). So I do this procedure:
I program the Softdevice (in my application S110 rel. 7.0.0);
I program...
I am using nrf51822 and I am trying to reduce the transmit range to 30 cm or less.Is it possible to achieve this. The reason I am doing this is that I will be working with...
Hi,
I want to use both SPI master & slave altogether, but when I include nrf_drv_spis.h upon compilation the following error occurs :
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
I am trying to find out the lowest range of nrf51822 but so far I coulden't find anything. Most of the time people are trying to increase the range.Thanks.
