nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
For a specific project i will need to have ability to monitor some 4G/3g/2G protocol stack L2/L3 messages. Is it possible? is there any documentation regarding this option...
Hello DevZone,
In NCS, we have many BLE Mesh examples that is initialed by:
The first argument is a structure that contains some input and output OOB callback functions...
Hello,
Currently I am implementing the nrfx qdec driver in our Zephyr project using the nRF52840 DK. We choose the nrfx driver as this provides events. I am using the nRF...
Hi.
I have designed a node with NRF52833 with +8db power antenna.But i got some issue in signal transmission over 1km range.Please review my layout and matching circuit...
I have the software installed and I am using the nRF52840DK with Ubuntu 22.04. The uart link is /dev/ttyACM0
When I start wireshark and do a capture on all advertising channels...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
