I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
hello:
My project is based on "esb_rx",NCS2.5.1，nRF52832.I need a Unique address for my product ,so I add flash read/write function for my projict, base on "soc_flash_nrf...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...
This question is in lieu of an issue on the repository, because I don't think issues are accepted there?
I noticed I was getting the following CMake Warning:
Could not...
I am running on demo "nrf-knx-iot/samples/light_switch_sensor".
I built the demo and burned it into my nrf52840dk successfully, but I could not see more logs.
I found...
Hello! We recently acquired a Nordic Thingy:91 for prototyping and it was working great until I came into work this morning and it was no longer showing any signs of life...
Hi Support team,
When I compile the application on the network core of nRF5340, the result is like below:
There is a 64KB SRAM1 with usage 0%, could you tell me what is...
Issue: No Interrupt Signal on GPIO0 Pin of MAX30208 Sensor with Xiao BLE nRF52840 Using Zephyr NCS v2.6.1
I was write a code for max302078 sensor driver but in this i want...
In some examples that use nrfx libraries it is necessary to extract a GPIO PSEL, which is usually done like this. Give the following DT definitions
``` leds {
compatible...
