Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
hi support team,
customer is asking how to add keep alive time in https request header,
i was trying to do this command as below: adding " Keep-Alive: 60\r\n" in XHTTPCREQ...
Hi there!
I've been digging through the code base but could not find a compile option to enable LOG_DBG() type output so that I can observe the JSON formatted packets sent...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
Hi,
How do I set the SPIM3 parameter so that MOSI is low after SPIM3 has sent a byte 0x01?
The test environment
DK PCA10056
SDK :sdk17.1
example :spim3
Thank...
Hi,
How to enable NRFX_LOG_INFO?
I ran the following test, but no nrfx log was found
example:D:\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056...
Hi
1.Referring to this tutorial, the customer tested the cat-m mode, and the equipment could not be identified by the customer instrument. How to deal with it?
2.nRF9160...
I followed the tutorial videos and when I connected the device using USB, the computer didn't recognize it and it didn't show up in the devices list in VS Code either. pc...
Hi,
I'm working on a project where we are receiving sensor data from a BLE peripheral (BL654), and publishing it to a piece of PC software via UART/ FTDI cable from a BLE...
hello
1.NRF52840 Upgrade APP+BL+SD from SD15.3 to SD17.1.
2.BL use pca10056_s140_ble_debug,APP use ble_app_buttonless_dfu.
3.Program batch file.
nrfutil settings generate...
I have a case where a maximum of 1.4V will be applied to an GPIO pin immediately before the MCU powers up (the voltage enables a boost converter, which then powers up the...
I see this message on my debug output whenever I connect an app to my device. I'm trying to find where the opcodes and status is documented but can't. Can you please point...
Hi, I'm using a nrf5340 custom board. In my program I am using MCUBoot but I would like to know how I can remove the second slot in flash to flash a big program. I'm will...
I have 4 Thread end devices commissioned onto a matter network and want to control these devices from another Thread end device by pressing push buttons. Is this possible...
Hi,
I am having some issues with the Co AP Client and Server on n rf Connect SDK v 2 . 1 . 2 .
I have flashed two n rf 528 40 dev kits with the examples , one with the...
