I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
I have a Nordic thingy 91 connected to nRF Cloud, and I see a message "Upgrade your firmware to view Network, Sim, Device, and Service Information" I have tried to update...
The nRF9160 is connected to the nRF52840 by MCU_IF0 ~7(GPIOs) in the Nordic Thingy:91. and I know to uses UART communication between the nRF52840 and the nRF9160. Can I know...
Hi
a way to reset nRF9160 is by pulling low the nRESET pin https://infocenter.nordicsemi.com/topic/ps_nrf9160/pmureset.html?cp=2_0_0_4_0_4_1#pin_reset
During the entire...
Hello!
I would like to try the following using my nRF52840 board: press a button on the board and then receive a notification on the phone. And the other way round , press...
I am trying to update the DUT(Device Under Test) via nrf52840 Dongle with PC(ubuntu16.04/windows10) by the command as below:
nrfutil dfu ble -ic NRF52 -pkg OTA_DFU.zip ...
Hi,
This is actually a followup ticket based on this: https://devzone.nordicsemi.com/f/nordic-q-a/56228/fota-dfu-over-internet .
Now the situation is a bit more concrete...
Dear all：
I want to control my central( 52840 ) device to connect with peripheral(52810) within a range （45-60m），i change the tx power，but it set -4dbm，the distance is just...
Hi, I'm developing new project, and during test I see that, if you quicly connect/disconnect/connect.... and so on, the app seems locked... Tu exclude my HW-FW, I tried same...
Hi,
How to auto-connect with my BLE peripheral without an external application?
Here, the Android mobile acts as a central, and the nordic chip act as a peripheral.
...
SDK15.0.0/SEGGER/Windows
Hi, I ran this example: https://github.com/NordicPlayground/nRF52-ble-long-range-demo .
Note: Added NRF_LOG_INFO("%s", p_adv_report->data.p_data...
Hi, I have a problem with DFU upgrade over BLE on nRF52840dk. For some reason,the upload speed is quite slow ~0.4kB/s. For this test,I used SMP server app and did the compilation...
I'm using DFU of 52840, .I find a question, my development board can work normal with ble_app_buttonless_dfu of nRF5_SDK_15.0.0_a53641a,but my product board can't work well...
When building an app with mcuboot as part of a multi-image build, how can I pass the app version to imgtool so the app_update.bin header gets created with the correct app...
Hello,
I am using a custom nRF52840 (SDK 14.2.0, SoftDevice S140) based board.
Our boards stopped advertising and upon debugging we saw an error in the peer_manager_init...
