I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Hi,
I'm currently programming a custom board using a nRF52832 ( using this wiring ). Everything was working great but I tried to play with SAADC and maybe did a wrong...
I am using the link below
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/getting_started_softdevice.html#getting_started_sd
with 3 options...
I'm having some problems getting the sections/observers to work properly. Using SDK v15.3 and Crossstudio for ARM v4.4.2
If I break at ( nrf_sdh.c )
I can see that the...
Hello, I have just started using nRF52840 DK and previously I have used development kits from different vendors so, I was wondering when developing which resources are available...
Hi All
I know this is stupid but I can't figure it out - either I've missed something obvious or not connected something properly (or at all).
Using the PCA10040 nRF5...
I have developed a custom board with NRF52810 (Rigado), a standalone CAN controller (500 kbaud) and serial communication (57600 baud).
The SW is based on the BLE_APP_UART...
Can anyone tell all the potential reasons for stack corruption? I'm debuging a problem where sometimes there is no stack trace when putting a breakpoint on the first line...
I have a project based on SDK 15.3
I've set #define NRF_LOG_DEFERRED 1
The project generates a high volume of log output over RTT
NRF_LOG_FLOAT_MARKER is a macro that...
Hi, I am using the nRF51822 with SDK 12.3.0
I am trying to make use of nrf_drv_spis driver included in the SDK.
My purpose is to have nRF51822 constantly be RX-ing over...
While investigating my stack corruption issue , I noticed that the RADIO_IRQHandler is always called twice in quick succession:
But the NRF_RADIO->INTENSET register only...
I'm trying to communicate between two devices (nrf52840 and teensy 3.6) over RS485, but I'm having some issues using the UART library in the SDK. I'm trying to create an interrupt...
Hi,
It all happened today after being used the board for a month. when I tried to turn on the board it does not blink LED5 nor does it show up in the device manager. I to...
Hello Nordic,
I have multiple Thingy52 devices upgraded to V2.2 firmware via nRF Connect application on my android phone.
Have been trying to add the BL Mesh light switch...
I want to read timestamp in my nRF9160 device and found that "z_tsc_read()" function in Zephyr RTOS will do that. However, I am not able to include the main library of the...
Hi,
We are developing mesh control lighting system with nrf52832, now we're able to control devices through mesh.
But now we're having problem with showing node state...
