Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Dear Sir/Madam,
In the NRF date_time_ntp.c, the fraction of the NTP message is completely ignored in the line:
* date_time_ms = ( int64_t ) sntp_time . seconds * 1000...
Hi there, I have a nrf54l15 pdk and i want to get any uart log with my kit. I tried the quick start hello world code but it wasn't load application core and reset device....
I sometimes have bonding issues. Most of the time, bonding works fine. But occasionally, It looks like the Nordic SDK on the peripheral sends messages too early. The peripheral...
Hello,
Our solution uses nrf9160 in smart parking devices that the user controls from a smartphone app, through the internet. Since commands come from the user to the device...
Just starting out developing for Nordic Devices and I've got a very basic generic switch working on the nrf52840 DK. I've commissioned it with Apple Home Kit / Apple TV serving...
Setup : nRF Connect SDK 2.3.0 nRF52840
Hi all,
I would like to add mcuboot update over Zigbee FOTA to my application. I am aware of that the bootloader update over Zigbee...
I include __TIME__ and __DATE__ strings in some files (main.c & commands.c) - I want these files to be recompiled everytime even if they
are not changed. I am using teh...
I just wanted to share this in case someone else runs into this as well. I was running into all of the same things as others where I could run the nrf_sniffer_ble.sh --extcap...
where can i find some simple examples that transmit / receivfe packets using the RADIO....
assume for the moment that i'll be implementing my own proprietary protocol atop...
Hello, I am trying to develop a 1000 Hz wireless gaming mouse. The mouse has a NRF52832 onboard and the dongle has a NRF52820 on it. (Cannot switch to 52840) I do know about...
Hello,
We have a custom PCB that includes an nRF9160 and nRF7000. We’re planning a hardware update to add external flash memory and would like to know if we can use the...
I'm currently working on a matter application on a custom board in NCS 2.9.0. In the documentation for the ipc_radio net core image the README at nrf/applications/ipc_radio...
Hi all,
I am trying to configure the NFC Pins for usage in an SPI application. However they do not even work for a simple nrf_gpio_pin_set after configuring them with nrf_gpio_cfg_output...
Hi
I have developed a PCB that will be used to control some sensors. The pins NFC1 and NFC2 are intended to be used as GPIOs. However, the default processor settings configure...
Are there any ways/workarounds/configurations to drive P0.9 on nrf52840 as an Input/Output instead of just being NFC pin.
Technically we should be able to drive this pin...
