I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
Hi There,
I'm interested to customize the eddystone TLM parameters as per the image below, which is replace the Battery voltage with Button detection On/Off.
I did...
I was able to successfully make the BLE Peripheral Eddystone Beacon Application in "nRF5_SDK_12.3.0_d7731ad" in Windows 7 32-bit (pca10040), using GNU Tools ARM Embedded version...
Greetings,
I'm fairly new to developing with Nordic ICs using the SDK, I have previously developed for some nRF51x MCUs using some modules that had an Arduino library...
hello , everyone
platform : NRF52832, SDK13.0 , project:\examples\ble_peripheral\ble_app_template
I meet such a problem, config app_timer in APP_TIMER_MODE_REPEATED and...
Hi,
I cannot get the interrupt on Timer1 to work. I have checked that the counter is matching the compare register by not enabling the interrupt. When I enable the interrupt...
According to the official suggestion circuit, I’ve deleted some functions which are useless for me, (the schematic circuit diagram and PCB are showed in the end) then I use...
Hi all
I'm using nRF52 DK with 14.2.0 SDK. I created a LED blink project for testing and extract its HEX file. I uploaded the program to the nRF52 over USB (J-Link-Keil...
Hi Nordic:
I use the nrf Connect to upload a new zip , the dfu progress goes to 21%,and then I get a error.
Error msg:
DFU failed with error: When writing 'CREATE...
hi.....folks
i am using nrf52832 and have merged the twi sensor with uart and timer but i am getting , i dono where to add my timer in main loop , see the code
help me...
Dear All,
I am new to using Nordic boards. I want to connect MAX9814 microphone module with nRF51 DK board to record the audio of human. I could not find supporting libraries...
