I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
HI,the current situation is that nrf52832 can not receive the ack_payload from the nrf24le.
nrf52832 as DEVICE,using the project NRF5_SDK_13.0.0\examples\multiprotocol\experimental_ble_app_gzll...
I am a beginner and I need to know how we can further modify the light switch example codes to access gpio pins and get some output from that.
I have run the example using...
Hi to all team members.
I am using nrf51822 working at 16 MHZ clock.
I have interface 3 sensors ECG, SPO2 and GSR sensor analog output to nrf51822 on 3 respective channels...
Hi
I have N number of beacons and one observer having nrf52832. I want to have the number of unique beacons available in the scanning range.
Do the s132 soft device provide...
Hi everybody,
I suppose our question is mainly in the title.
ThingyLib version is 1.0.2
https://github.com/NordicSemiconductor/Android-Nordic-Thingy/tree/master/thingylib...
