Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
This is with the nRF 5 SDK (17.0.2) and the S113 softdevice.
We have another microcontroller connected to the nRF52833 over UART and external flash. We modified the bootloader...
Hi,
I'm currenty try to code GPIO wakeup from System ON sleep with system_on_wakeup_on_gpio as a reference.
My circuit is powerd by solar panel via control board. In this...
Hi,
I would like to know what is the default state of GPIO pins when nRF9160 is power ON for the first time, and it has the pre-programmed FW from Nordic
Hi,
What is the expected format to pass to nrf_cloud_agps_process()? I am working on an LwM2M server and want to be able to respond to /50001/0/{0,1} request coming from...
Hallo,
I installed the ncs and Zephyr environment following mainly the guidelines from nordicsemi, a few changes were necessary to use Eclipse. The installation process...
Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
I am testing out the nRF Cloud MQTT multi-service example on my nRF9160 DK board. When looking at the GPS data on the cloud it is not very accurate and does not track my location...
Hi!
I am experiencing some odd behavior from the modem, and I hope you can help me understand it:
After I disconnect from LTE using lte_lc_func_mode_set(LTE_LC_FUNC_MODE_DEACTIVATE_LTE...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with a connection to an external MCU (#define MQTT_MESSAGE_BUFFER_LEN 8192) We tested...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
Hi.
I'm working on a project based on the USB CDC ACM sample from Zephyr, which builds correctly for nRF5340DK, but gives an error when trying to build for nRF9160DK due...
Hello,
I am working on a project based on the nRF52810 custom board, I need to use several slave nodes to communicate to the gateway node/ server.
I need to improve...
Hi,
I want to use the nRF9160 SiP to connect via NB IoT to AWS IoT server but I don't want to use any SDK, I only want to use AT COMMANDS, there is some process that I could...
Earlier I created a project in SES for nRF5340. The simulation and debugging was quiet simple and easy to find the fatal errors, run time errors etc. Same features are not...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values from 0 to 10 using ADC with ble_app_uart. I have combined SAADC code and BLE_APP_UART code...
