Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello,
in our product we need to have the possibility to set name higher then 31 bytes.
We modify the code according the tick
devzone.nordicsemi.com/.../sd_ble_cfg_set...
I can connect same sensor using nRF connect app. See attached snap shot.
The BLE connected Pressure sensor is advertising the Unknown Service using UUID : -- 18FF (First...
Ladies and Gentlemen,
I was wondering about the maximum clamping current of the Body Diodes of the nRF9160's IOs. There is no value stated in the product specification....
This might be a naive question, as I am a novice in this field.
I am making something similar to ble_app_hids_keyboard in sdk11, it will be configured as a consumer device...
I am using windows 10 and I was trying to operate my pca10028 board for a blue tooth connection. I pressed the reset button a few times but now its not working and only LED...
Can a corrupted InfoPage of the nrf24le1 be fixed from an ELNEC/Dataman programmer? I have read on the forum that th InfoPage can be restored from Nordic kits/IDEs, but I...
I am using an nrf52832 DK with Zephyr and I have a component that require a block of code to run uninterrupted. Specifically I am using HX711 with four load cells, and the...
Hi,
I want to display a picture with a screen (80x160) with st7735 and sdk 15.3 (segger embedded.)
I have some problems.
I use the function nrf_gfx_bmp565_draw, so I...
I am using the NRF9160 for SPI using an external Flash. After using the 'http_application_update' samples, I was able to get the value of the data written on the external...
Hi, I am a MCU developer searching BLE MCU to develop some IoT project.
I would combine nRF series and LTE NBIoT module for IOT project.
And I need to integrate many different...
Hello all,
I am trying to use my nRF52832 DK for a wireless camera shutter for my phone. I have reviewed the example code from SDK 15.3.0 named ble_app_hids_keyboard as...
Using SES, nrf52840DK, the onboard debugger.
I am able to set a breakpoint and use condition like x == 5.
I am unable to use anything but the == operator. In SES I...
On line 904 of nrf_log_frontend.c there is a log message to indicate the backends are flushed – but this message adds a log to the queue. If auto flush is enabled, this can...
