I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am keep trying to get the BME680 example to work with the nRF52840-DK using Zephyr.
I check and successfully find the node for the BME680, but "device_get_binding()" for...
Hi,
I am using
I am able to list BLE devices using the below example.
SDK = nRF5_SDK_15.3.0_59ac345,
Example : nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_gatts...
According to this thread, iPhone 11 Pro supports Long Range (Coded PHY) : https://devzone.nordicsemi.com/f/nordic-q-a/33060/is-there-any-smartphone-with-supporting-of-bluetooth...
Hello,
I am upgrading to SDK 17.0 from 15.0.
When I try to to compile my project i get this error:
../_Release/Release_Commercial_Debug/Main/Exe/Main.elf section ...
Hi,
I followed the tutorial in the Github and create a custom service. (Github: https://github.com/NordicPlayground/nRF52-Bluetooth-Course )
1. I use the ble_cus_custom_value_update...
I have an issue with my Thingy:91
1) I unboxed
2) I successfully connected to my Windows machine and updated the modem firmware
3) Turned off power
4) Turned on power...
I would like to add a simple ble BAS (battery service) to appear along side my custom services... but for the life of me I cannot find any information, or tutorial on how...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
