I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
I am using nrf52832 for button less DFU. DFU is working fine when CONFIG_NFCT_PINS_AS_GPIOS is not added in applicaton. When added seems like code is getting reset at bootloader...
I have problems compiling code with modem info support on. My basic problem, I want to establish which modem FW version I am running on.
I added
MODEM_INFO_CONFIG=y
...
We successfully built the mesh bootloader, but want to get RTT working with the bootloader logs inside SEGGER.
We were following this two posts post1 post2 to achieve our...
Hello guys.
I just donwload new version of SDK 1.0.0 for NRF9160 and try run mqtt_simple demo. I didnt change nothing there and there is problem.
I have the follow log...
Hello,
Currently my beaconing application draws approximately 10uA @ 1000ms advertising interval. I am having trouble getting the chip into system power off mode so the...
Hi,
We would like to upgrade an existing product (Bluetooth SIG registered) on the market to the newest release of SoftDevice. Do we need to re-register at Bluetooth SIG...
Hi,
I'm working on a bootloader based on the "secure_bootloader/pca10056_ble" example. Everything works fine until I send the new application binaries (.zip file) and the...
Hello All,
I am working on the NRF51822 custom board.
I am Using the SDK 12.3 with s130 (PCA10028)
1.) Is it right sdk for nrf51822..?
2.) Facing issue in configuration...
Hello,
I am working on a beaconing application and I was wondering if it is possible to run the code beginning with system off mode and wake up the board with a button press...
Hi,
we are using a sensor which streams out buffered data to an ios or android app. If we face a disconnection the data gets buffered and send when reconnected.
But the...
Hi,
I am using customized nrf52 board with softdevice s132
I am trying to interface External Flash (MX25L64) using spi.so when ever i am trying to send any command /data...
Hi
I figured out, that the macros in nrf_esb_resources.h are wrong.
You can find the used resources (PPI, TIMER and SWI) of the ESB library in Enhanced ShockBurst...
What is the operating and storage temperature range of nRF52840-DK development kit and USB dongle? We need to use these evaluation boards at a temperature range of -20 to...
Experts,
I'm trying to use NRF52480 Dongle to communicate over UART serial port. On the forum I found that pins 1.10 & 1.13 are used for TX/RX. I learned that flow control...
If i buy a raw nRF52832 chip and design the circuit by myself, how can i pre-programm the serial bootloader in it? So i could use the FTDI Basic (or an FTDI Basic -like device...
