Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Good day, I have noticed that cellular reception is very weak using an NRF9151 SMA DK. For more context, we have been using SIMCOM7080G modems in NB-IoT mode with all bands...
1. 1.8V Power Domain & Pins 1, 2, 3: - Our design does not utilize a 1.8V supply; we are operating exclusively on a 3.3V power rail. - Please confirm the required connection...
Problem After successfully establishing a nrf7002ek (or nrf7002eb) WiFi connection to the local network with a nrf52840dk (or another nrf52840 board), AWS IoT (based on the...
We are developing a multimodal optical, biometric, and motion sensing platform utilizing the nRF5340-DK (PCA10095, v2.0.0) as the master controller and wireless host. The...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
After deletion of my three devices from my nRFCloud/Memfault account, neither I, nor a colleague of mine are able to add the device for use with the cloud. The message we...
Hardware Config : nPM1100-EK (PCA10123 0.8.0, date code 2022.25), SW1 = GND (automatic), SW6 = VSYS/VSYS (VOUTB = 3.0 V setting), VOUTB measured 3.12–3.13 V at 3.7 V in using...
I'm using nRF Connect SDK (NCS 3.1.1) with LVGL and newlib in a application. I encountered two related problems that I believe are caused by a conflict in the Zephyr LVGL...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hello,
after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
Hi,
I have B0, mcuboot and then application as my partitions. We plan to support upgrade of both mcuboot and application.
Based on this below Kconfig snippet, it looks...
I have looked through the documentation but do not see any mention of CTE, so I assume it does not support CTE. I just wanted to ask and be sure as I am new to Nordic and...
