I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Dear Company,
I would like to ask about start-up time of this product nFR24L01
Max 1.5ms start-up from power down mode
Max 130us start-up from standby-I mode
1...
Hi, everyone
how to increase the peripheral link count in multi role lesc example . even i have tried with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT by increasing the count, i am...
I have followed the dfu bootloader instructions for dfu secure ble example in both sdk 15.3 and 15.2 versions. I copied pca10056 folder to pca10059 and changed the board definitions...
Hi. I'm using nRF52832, SDK13.0.0.
I'm developing not only peripheral side but also central side.
I already made peripheral side referring to DFU example code.
But i...
I was trying to measure the current used by the nRF52840 on the DK. But it seems like i have messed up.
The debugger LED does not light up
The nRF52840 SOC seems to...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
I tried to add a BAS service to a project with an LBS service (ble_app_blinky), but I cannot complete the services_init() procedure for both services.
Is it possible to...
