Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello
I am currently trying to read data and save the timings of it. When pushing a button on my custom made PCB, the microcontroller goes to the handledata function....
Hey,
So I've been using the Verizon SIM card supplied by nordic with our nRF9160 dev kit. I never really new how the APN was getting configured because it just happened...
Hi, I have DK-52840 where the ATMEL ATSAM3U2C is the on-board debugger. I replace firmware via my J-LINK ULTRA+ JTAG through 10-pin connector on-board, I used J-Link Commander...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/hardware_driver_pwm.html
Where are more docs like this explaining how to use the drivers?
Hello, everyone, I am a fresh guy using nrf toolbox to read UART (52832) logs. Now I installed nRF Logger and try to save the UART log file. Does anyone can teach me how to...
Greetings to all, I am trying to debug the PrnRF Connect Programmer with visual studio code, but I can not find a way to achieve this. They could give me a hint of how to...
we have a linux gateway with an nrf52832 connected via serial port. the gateway communicates with a modified connectivity HCI application on the nrf52. the gateway device...
Hello everyone,
I am using nrf24l01p. It works fine but some times gets hang, doesn't receive data at all. I am sure that this is not the problem of micro controller because...
I am using the original board. Crystal of 32kHz has not been mounted on this. So, I want to use the internal RC Oscillator. In addition, I use a hrs example of nRF5_SDK_11...
From the product spec, I can operate in either low power mode or constant latency mode. It is not clear how much (or what mechanism) compromises the latency when low power...
Hello,
I'm developing an application that is sending data every certain seconds in a mesh network and, in order to reduce the power consumption, I wish the node enter...
i am using latest version mesh sdk 3.1 .. i want to interface two boards and want to check the bidirectional using text message, example if client sending the hello message...
Hi,
How can I Understand why the nRF9160 is disconnecting from the network?
How can I read the modem trace bin file to understand whats going on with the modem ?
Hello,
Do you have a soft device that integrates both Bluetooth and USB on the nRF52840 ?
I want to program a firmware that uses both and I'm wondering if you have ready...
What changes are needed in SDK V15 sdk_config.h so nRF52832 can run on internal RC oscillator?
I am using the BLE UART example, nRF52832 with Soft device s132_nrf52_6.0...
