Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
Hi,
I am trying to run the ble_app_uart_coexist example on my nRF52840 Development board.
I followed the above steps for configuring the example to work.
I copied...
how to include SPI Master code in ble_app_uart sample code of pca 10028(nRF51822) board. its soft device is sdk 10.0.0 (s110). Please share me a sample code if you have. ...
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
