I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am using the nRF52840 dongle to gather data via peripherals and send it via a serial port similarly as the cli example, for that I'm using the nrf_cli_fprintf() function...
Hi all.
I want develop device with nRF9160. goal - to get smallest size with chip antenna.
I not so good in RF design, so usually I using recommendation from datasheets...
Hello,
We have an nRF9160 DK and have successfully set-up the tools necessary to re-flash and write firmware for the DK using Zephyr and SEGGER Embedded Studio. We are planning...
Hi
I have tried to pull down the updates for the Zephyr project to for the mqtt_simple example. when I do a git checkout master and a git pull all goes fine. but when I...
Sir,
I have seen example pgm for communication between UART and BLE, and another pgm which communicates between 2 UARTs. But for my project I need 2 UARTs and the BLE together...
Hey,
previously working with BLE devices I had manage them reading/writing its characteristic. To control my new device I have to write the value into its handle ( i. e...
Hello Sir,
I have a PCA10090 (nRF9160) DevKit and it was working fine with Asset Tracker Example. Kit sent data to nRF Cloud last month. Today i have again verify the...
Hi, I developed a simple app that connects to a Bluetooth device, receives some data from that device and output it to the uart. As a receiver I have a custom board with a...
I have to develop a project for nRF51822 but I can't find tools that work. I tried SES and Eclipse and none can compile the examples of SDK12 (the last one that supports my...
Hello,
I've recently purchased the fanstel BT840F evaluation board which is based on the nRF52840. I understand that you cannot directly program the BT840F evaluation board...
Hi!
I just saw the MQTT example that has been merged in the master branch and tried to run it on my DK (NB-IoT). Without changing anything in the code or configuration the...
Following my last post a few days ago, I was finally able to communicate with a slave via the TWI interface, thank you very much for your help! This time, I have a problem...
Hi,
I'm using nrf52832 as host and peripheral concurrently, with soft device s132. I know that peer manager can handle both host and peripheral.
I now have a need to remove...
Hi everyone,
We are (still) in the process of evaluating the nrf9160 with the DK.
Our use case is the following one: we want the nrf9160 to send periodic messages in PSM...
Hi, We've developed an IoT platform that runs on Raspberry Pi's that has just been released and we're actively seeking beta testers (see www.omniot.com ). In short the platform...
