Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
hi :
i send characters of SPI master of 52DK to SPI slave of our target board(Nordic nRF52832), our target board use SDK v12 spis example. but spi slave event can not rececive...
I am using SDK 12.3.0 and S130 2.0.1.
In example ble_app_uart and ble_app_uart_c,
Central setting:
Peripheral setting:
Why it took so long to discover service...
Using the same connectivity firmware, a dfu update using nrfutil takes about four times as long as the same update using nrf connect. I have to setup dfu updating in a production...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
Hi,
I am trying to use Segger embedded studio for my project,
I get these errors:
Building ‘ble_app_uart_c_pca10028_s130’ from solution ‘ble_app_uart_c_pca10028_s130...
hello,BPROT does not work normally when i am debugging BPROT.
when i set CONFIG0 bit2 to 1,that is NRF_BPROT->CONFIG0 = 0x00000004,then i want to erase block 2(start address...
I am having a hard time turning ON semihosting. Here's my setup:
- Debugging is done via Eclipse GDB SEGGER J-Link Debugging with the Enable Semihosting checked and console...
Hi all,
I have a problem. I add NUS to light switch proxy . But the first time, I use nRF_UART or nRF Mesh connect to my Dev Kit. Then, I disconnect , I see it run MESH_GATT_EVT_TYPE_DISCONNECTED...
Hi,
I'm trying to set up a custom project with all the mentioned components. I build the bootloader, I'm using the `s140_nrf52_6.0.0_softdevice.hex` for the softdevice and...
Hi,
When i tried the light switch example from the Mesh 2.0 source code, i got the error code NRF_FAULT_ID_SD_ASSERT. when it is doing the provision process.
The last...
hi Nordic Support Team,
One Of Client has a Machine with Bluetooth Sending some Data every 1min.
They want to capture this data and Send this data through Mesh. Is it...
Hello,
I am using sdk 12.2.2 and nrf52 customised development board. My challenge is as follows.
1) I am getting success in fds'_write function.
ret_code_t ret = fds_record_write...
We planing to use the NFR52832 with heavy algorithm (Real time ECG analysis) with light BLE use. Does the BLE have higher priority that can slows the algorithm?
I have a wireless project. Requirements as:
Support platforms: Desktop/Laptop and mobile, Pc/Mac/IOS/Android. etc.
many connections: flexible but can support 100+...
