I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I'd like to inquire what effect the SAADC TCONV parameter has on the results of the SAADC. The SAADC section in the datasheet specifies it can range from 1 to 7, giving...
Hi,
I'm sending IPv6 traffic between two PCs over a DECT NR+ link: two nRF9151, one FT and one PT, NCS 3.4.0, modem firmware mfw-nr_nrf91x1_2.0.0, using the l2_dect stack...
Hello
We have nrf54l15 as a host and main MCU along with nrf9151 with SLM build.
We are connecting it to nrf-cloud, previously we used only nrf9151 with nrf52 connected...
Hi there,
We would like to know when the Nordic nRF52840 will support the Matter 1.6 full commissioning exchange over bidirectional NFC communication. Or is this feature...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi! We have recently upgraded nRF Connect SDK. Since this change, some of our users experience issues with uart - two nRF52840 communicating together. We have not been able...
Summary
We implemented BLE OTA on the nRF54L15 DK using nRF Connect SDK Bare Metal v1.0.0 and it works with the single-bank DFU flow. For our product we want dual-bank DFU...
Is it possible to use the I2S_FMT_DATA_FORMAT_PCM_SHORT format with the nrf53 I2S Interface, which is documented in the zephyr API reference ? There is nothing about it in...
Hi
We need to stream audio from nRF5340 to LTE module. But our LTE module support PCM format audio.
I checked that nRF5340 support mono audio streaming through I2S. Is...
Hi support team,
We would like to evaluate channel sounding using your evaluation board.(nRF54L15-DK and nRF54L15-TAG)
We have been able to verify channel sounding using...
Hello,
I have a project based on nRF9160, that uses nRFCloud over CoAP. It uses SDK 2.8.0, with functions such as functions such as nrf_cloud_coap_json_message_send() and...
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
Hi all,
I want to ask which silicon version are the DK stocked at Mouser or DIGIKEY for the product nRF52LM20-DK. Is it version 0.7.0? Thanks!
2.16.1.2
2.16.1.2
2...
