Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I upgraded Toolchain and SDK in VS Code to Version 2.6.1.
Now the build is failing.
As far as I can see the wrong CMake will be used - from Visual Studio but it...
Hello,
I'm trying to implement the MCU BOOT in order to introduce the Firmware uptdate but I get the following error:
I'm trying to reduce the RAM usage but with no...
I am new to BLE development and was wondering how I can read the data published by the A&D Medical Blood Pressure Monitor with the nRF5340 acting as a central. I can connect...
hi support team,
customer reported on problem that one product is ok when in factory, but now is in problem after delivered to office.
i had onsite debug and find out...
We are nRF52840 in one of our products. When we use SYSTEM OFF mode with with hardware design, current consumption is around 3uA but when we use SYSTEM ON mode with RAM retention...
BLE settings:
1) Advertising interval: 500 ms.
2) I am not explicitly turning on the DC-DC regulator; I am using the default settings.
3) Tx payload: 31 bytes.
According...
Dear All:
I have followed the procedure as shown in the following to make a Mesh heartbeat application.
I started with the example of ligtht switch client and server for...
The documentation for CONFIG_MBEDTLS_PEM_CERTIFICATE_FORMAT in nRF Connect SDK says:
By default only DER (binary) format of certificates is supported. Enable this option...
My question is completely wrong (0x2880 is alloc failure, not parsing failure)! Please ignore.
When using the nRF Connect SDK mbedtls implementation to conduct a TLS...
Hi,
For the nRF52840, can we use another pin than P18 to realise the Pin RESET functionnality?
I can write the register NRF_UICR -> PSELRESET with numbers other than the...
Hi Devzone,
I am facing an issue in my application where my device is working as a BLE peripheral advertising for connection. The device stops advertising after connecting...
I'm trying to download and flash an MCUboot image at runtime. All goes well, the image is flashed to the secondary slot, confirmed, and marked for upgrade. The secondary slot...
I use the nrf_dm demo program, when using the nRF52840DK development board, the program can print the log normally.
Then I changed the build configuration to nRF52840Dongle...
Hello,
I have a custom nrf5340 board with a simple firmware flashed on it (turn on red led). My board has a hall sensor as a turn on/off switch (latched). If I connect it...
I used nRF52840 board with SDK 17_1_0 ,
Using FDS I am able to read and write data into flash when nRF52840 board Continuous ON,
But when i Make nRF52840 board Power OFF...
