GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi
I use nRF7002-DK, SDK:Ｖ2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
Hi,
Because I wanted to add custom features to mcuboot, I had to use custom mcuboot.
I also used sysbuild for multi-image building.
The documentation tells me that...
Hello,
I am currently working with the nRF5340DK kit.
For my project, I need to incorporate some additional custom checks/code into the project's bootloader(MCUBoot)....
hardware:nrf5340dk
The above 45 pairs of IQ data are a set of data that I have received.The maximum amplitude of the IQ data I received seems to be only 128, which means...
Hi I am implementing dfu over modbus. Basically I managed to integrate all the steps (transport, set pending, restart, confirm).
What I'd like to do is to implement image...
Good afternoon,
I have recently purchased a PPK2. I have installed nrfConnect for desktop and Power Profiler on my Ubuntu 22.04 machine. I have connected the PPK2 and...
The example for LZ4 works fine, however I want to use the frame format and not block format.
Therefore I added #include "lz4frame.h" to my main.c and tried to use LZ4F_compressFrame...
My project is developed on nRF52840, it needs to communication with a mobile device through BLE, nRF52840 is as central. The mobile device starts BLE advertising, then, nRF52840...
hello guys, I want to use nrf52840 for my project is it possible to use ST Link for it. because I don't have SEGGER J-link ,if it is possible how can we use it please let...
Hello
I am trying to connect the nRF9160 -DK board to nRFCloud using CoAP protocol. I have written an application for this case. I tested my application with two different...
Hello
I'm trying to connect nrf7002EK with SPI3 with nrf52840DK,
NCS/Samples/WiFi/Shell, but I came up after Flash
The error shown in the image below
I would like...
Hello,
I'm trying to erase/read an external flash ( MX25L6433F) connected to an nrf52840 using nrfjprog. I've created a .toml file for the configuration, see attached. The...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
