hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
I am plugging the nrf52840 Dongle to the USB port, the computer beeps as it recognizes a new USB device, but when I open the Programmer app from the NRF desktop connector...
Hi,
I am a very beginner in Python and BLE. I would like to use a nRF52840 Dongle to connect to a Bluetooth Device, send 6-Bytes data in the 1401 section and also perform...
Hi All,
i have been working on two i2c devices
1. MPR121, which has slave address (0x5A)
2. PCF8583, its address is (0xA0).
I am using Zephyr I2c api for the same...
Hi,
I would like to ask on where can I find or set the advertising duration or on how long the advertisement would last?
I am using zephyr, nrf52840DK. I want to be able...
Hello,
So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link...
Hi,
Is it possible to perform a HW reset of modem core inside nrf9160 device? If yes, how is this HW reset requested?
Thank you very much...
Regards,
Emerson ...
proj.conf:
nrf52840dk_nrf52840.overlay:
code:
Pretty straightforward. I've looked through the nRF52840 Product Specification and there is no mention of data bits...
From zephyr/samples/sensor/lsm6dso, I found the following code using sensor_channel_get(). API from sensor.h.
}
However, there are more driver API in zephyr/drivers...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
I'm trying to connect my nrf52840 to the App but I have error message and impossible to continue ...
Here the log of the app standalone :
2022-10-07T21:50:58.341Z INFO...
