I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
Which BLE dongle can we use on PC in order to communicate with nRF52810 and nRF52832 chips?
Is there a desktop version of "nRF uart app" for reading and writing...
Hi all!
I want to run OTA DFU over Thread from a RPi3. Previous tests from a PC were successful.
I installed nrftuil: sudo pip3 install nrfutil==5.2.0
I added the...
Hello.
I am wanting to send an infrared signal from my nrf52 DK (pca10040). I've found code online for sending custom IR signals using pwm and a gpio pin. The IR signals...
Hi! We're developing an app which connects to BLE devices for different purposes. We've successfully enabled MITM using windows(an example from Microsoft) , but are having...
Hey, I'm trying to install the cat tracker application. When I'm executing the npm ci command. It is prompting the following error
ubuntu@ip-172-31-25-55:~/aws/nrf-asset...
I am trying to code a cycle power service and I need to add a server characteristic configuration descriptor. This service is probably the only BT SIG service that uses that...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
Hello!
I try to run FatFS example (SD card example, pca10040) from nRF5 SDK on my nrf52832 (ebyte e73) with microSD card with no success. No matter what I'm still getting...
Hi,
I am trying to get the time and UNIX time after LTE connected. but getting 0 only.
please log
date_time_update() function does not support in SDK 1.4.2 so I...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
