I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Dear Sir,
I use the nRf52840 DK (PCA10056) which be a ICE to download FW and 3V DC power supply for my DUT.
the 3Vdc connect to Vdd.
I use the DK 3Vdc be my power supply...
Hello,
Here is some information from my environment :
nRF9160 DK
SIM iBASIS
Country: Suisse
Operator: Swissom AG
roaming mode
Use LTE Link Monitor
I...
Hi,
I want to use tne NRFX SPIM module for reading and writing an external spi flash (at25df011) .
I looked at the example in order to reuse it or base my application...
Hi all,
I'm working on a project in SDK 5 (V17.0.2) on a custom board using a raytac nrf52840 module. IDE is segger embedded studio with a J-Link interface to the hardware...
The device we are using is nRF51822. It uses a bootloader from the Nordic SDK 11.0.0
The boot-loader we are using for the nRF51822 has several blocks of code in the SystemInit...
Hello,
I'd like to enable an instance of SPIM2 master (base address: 40023000) in SDK 17.0.2 for SPI operations. In sdk_config.h, there are two options, NRFX_SPIM2_ENABLED...
I am trying to run the heart_rate_collector.py example in Nordic's pc_ble_driver_py library. When I try to execute the program, I get the following error:
Command used...
Hi!
I'm trying to do the TCP example with the nRF5_SDK_16.0.0_98a08e2, a nrf52840 DK board and a Raspberry Pi 3 B+ as a gateway but I got some problems.
For connecting...
Hi, I'm testing the ICMP example, using a Raspberry and a custom board with a nRF52840. I follow the instructions on the "Connecting devices to the router" found in the infocenter...
hello,
i am using two customised nrf52840 boards and this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo to get the maximum range between two boards...
Hi.
I have NRF52840 with softdevice and GPIO0.7 and 0.27 connected to DALI CLICK and set up and 0.7 - IN, 0.27 OUT. I'm also using TIMER2 for running callback every 104us...
I'm using nRF52832 with an external motion co-processor. As a part of a robust reset strategy, I want to connect a single nRF52 pin to the co-processor's nRST pin to generate...
Hi
I'm using NCS 1.4.0 and SES. If I change the setting in Serial LTE modem to CONFIG_SLM_CONNECT_UART_2 for external MCU connection, I get an error msg from SES: Cannot...
Hello,
I am using "nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730" for NCP as well as other thread devices. nrfutil version: 5.2.0 RPI3 image: RaspPi_OT_Border_Router_Demo_v3...
