I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all, I am trying to use the nrf52840 dongle with wireshark, I was having permission errors trying to open the device in the program section of the nrf desktop suite running...
Hello,
we think about using an nrf52820 for a multi role solution. I know from the Compatibility Matrix that the S140 is supported and qualified for the nrf52820. What...
hi,
we are trying to add third sensor to the multi sensor example , new sensor is of type binary_input (0x000F) ZB_ZCL_CLUSTER_ID_BINARY_INPUT.
We are unable to subscribe...
I use nRF Connect for desktop / Bluetooth Low Enery Apps + nRF52840-DK.
When run 'start scan', In rare cases, very small RSSI values (-103dbm, -104dbm ...) may be reported...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
I have a custom board that I have programmed using the UART_BLE example. The code executes and I know I am advertising since LED1 blinks meaning it is advertising but for...
I am testing the Sensor example in the Mesh SDK.
For my implementation I need three properties that are given by the BT Mesh specification. (Properties 0x004F, 0x0057, 0x0059...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
Hello DevZone,
PCA10040 SDK 15.0.0 SD132
I written my own SPIM driver which uses the list function to read in a few bytes. I've set up my list as the example in the...
Hi,
What is the difference between performing a reset by using the function sd_nvic_SystemReset(), and performing a reset by turning the power voltage off and then turn...
I used "nrf5_SDK_for_Mesh_v4.2.0_src.zip" and "nRF5_SDK_V16.0.0", When I used scan_start() command, I saw Light_Switch_Server device and Light_Switch_Client device on the...
We have fabbed a PCB for the nRF52840 that has a QSPI chip. The pins are different from the example in the SDK. I was trying to get the SDK example (examples/peripheral/qspi...
Just test SDK17.0.2 serial DFU demo project on Nordic PCA10100 board by USB serial.and use s140_nrf52_7.2.0_softdevice.hex
Got below exception. Any clue for it please? ...
Hi,
I have my application based on nRF52840 device.
When writting a wrong passkey, my device is reseted.
Which can be the reason? I have already implemented event PM_EVT_CONN_SEC_FAILED...
