Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I want to use a comparator without interrupt.
The measurement is not time critical.
Therefore, I chose the LPCOMP.
For initialization I use the following code:
For...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
Hi,
I am working on a hub based on a raspberry compute module. Zigbee support is enabled by a u-blox (or Rigado) BMD340 module connected via UART to the compute module....
I have uploaded nordic thingy 91 with lte_ble_gateway program and modified it so that it can connect with 7 devices, however when i try to connect the 6th device I get bluetooth...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
Hi teams,
Recently, I made a custom board based on nRF52833 DK.
It works fine until now, and most of things works well.
But, I cannot make the board to show logs in...
I can see advertising packets of a device using an nRF51822 in Wireshark (example packet capture here https://imgur.com/a/maV6kbb) . But can't see them in nRF Connect on Android...
Hello,
I'm using the peer_manager in a GATT server project, after a first bond was created, I want the peripheral (GATT server) to advertise with ADV_DIRECT_IND, once the...
Hi,
I started development of nRF51822 with Keil(V6) / nRFgo / Segger etc..
I got SDK and exxample from here ( https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v6.x...
