Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello support team,
I am using your product through a module vendor and I have a question regarding errata 197. If the DC/DC regulator only has problems in low power states...
hi... i am using nrf52840 and nrf52832..... mesh sdk 3.1 latest version ....
in this case i am using client as nrf540 and server as nr52832 .... i have debugged the light...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I am working on an nRF52832 BLE peripheral prototype which sends bulk data to a central as bursts of large notifications. I am encountering an error where the connection gets...
We are manufacturing 2 types of gas sensors that communicate BT LE. One use an nRF52832 and the other an nRF51822. Will the nRF52 dongle communicate with both of these? Is...
Hello
I am currently programming with keiluVersion4.
Previously, I used "fatfs example" of SDK_15.0.0.
So trying to test the function of BLE, trying BLE communication...
Hi ,
I'm working on a 2.4GHz wireless microphone project now.
I want to make a scheme of two microphones transmitting to a single receiver(2T1R)。And ,i have tested this...
Hi, Andreas.
Following the guide you find in the document " Buttonless Secure DFU Service ", I get errors while trying to compile. In order to ascertain were is the problem...
How to realize the USB HID interface and PC data transmission?
I want to connect my computer via USB hid protocol for communication
This is my code, but can only send...
Hi everyone,
I am a beginner for BLE software development with MDK-LiteV 5.26.2.0.
Target device: nRF52832（EKSHCNZWZ made by Taiyo Yuden）
SDK: nrf5_SDK_15.2.0_9412b96...
I use the example from nrf51422 ble_app_uart_c with SDK_12.3.0 to connect via BLE to nrf52 usbd_ble_uart. When sending data that exceeds the length of one BLE packet (for...
